Nokia Care Suite PST 5.0 5.0.60.1409

New version of the Nokia Care Suite Product Support Tool 5.0 is available.
It provides support for the Nokia Windows Phones (Lumia), Nokia X and the latest Asha devices and products supported by the Testing and Tuning tool. Installation package and latest version of User Guide Document are attached.
For the products that are not supported in this release, old PST and Multi SW Updater version 2011.50.2 or Phoenix release needs to be used.
 
New features in the Care Suite 5.0
– Support for Nokia X (RM-980). Note: For device detection, user needs to manually enter code: *#*#2273#*#*  on device dial-pad and enable WinUSB mode by selecting it on device’s screen. Same action is always needed after finalized flashing.

– Application update works from version 5.0.51.1406 to this release.


Changes & Error corrections from previous version
Please note:
Offline installation: Uninstall previous version (5.0.51.1406) manually before installing this version.
Only the new Common Data Package Location (SR1315) is supported by default. If you need to use other Data Package Locations, they need to be added to the preferences manually.
Do not use Care Suite 4.0 and 5.0 simultaneously. They can be installed on the same PC and launched from the Nokia Application Launcher but not run at the same time.

If it seems that all features are not available on the left hand side of the screen, please click the small arrow next to the list. More features will be shown. This may happen if your screen is not maximized.
Lumia / Windows 7 phones will reboot when they are disconnected – please wait for the phone to restart
Installation of FUSE drivers may take a long time. Therefore it is recommended that the Windows Automatic Driver Installation is disabled from the Control panel. Please go to Windows Control Panel -> System ->Advanced System Settings ->Hardware ->Device Installation Settings and select “Never install driver software from Windows Update”
PC must be connected to network, meaning that Ethernet cable must be connected to PC and connection needs to be configured to work properly. PC must be able to connect to for example internal network, but it is not necessary that PC has an online connection to Internet.
 
Known errors & limitations
FLS-5 Drivers included in the installation package do not support 64-bit WIndows operating systems. Therefore Care Suite PST can not be used for servicing phones which use FLS-5 (USB_FBUS) connection.
Please do not use diacritical signs when selecting installation path for NCS.
Recovery or Refurbishment Flashing for Lumia Series Devices may fail on first attempt. Please try again, it works the second time around
Asha drivers don’t install when devices are connected via USB hub (on win7). Hub works if user installs drivers first via straight USB connection.
PST release 5.0 can be installed on the same PC with all current Nokia Service Software Applications, but simultaneous use with earlier PST version 4.0 is not possible
Audio input test with RM-899, RM-900 and RM-902 require AHJ headset.
In case of OMTP AV connector the microphone signal pin is switched with ground and the test fails silently.
(no error returned from the device).
Chess patterns do not work with RM-839, RM-840, RM-841, RM-948, RM-949, RM-950, RM-952, RM-953, RM-954, RM-956, RM-957.
The error is on device sw side.
Multi Software Updater 5.0 issues with devices RM-944 (Nokia 108 Dual SIM) and RM-945 (Nokia 108) Multi Software Updater 5.0 has some problem with multi refurbish for devices RM-944 (Nokia 108 Dual SIM) and RM-945 (Nokia 108).
In order to fix this problem please disable Refurbish Logs in preferences. Please follow the instructions below on how to solve this problem:
– Launch “Multi Software Updater 5.0” then go to menu File –> Preferences;
– In preference switch to “Logs” tab then uncheck Refurbish Logs Enable;
– Click Ok button
 
MSU
• When using Multi SW Updater, the recommendation is to use it with up to five devices that are the same model and start the refurbish to every device simultaneously.
• Do not start 1st flash-round with full amount of devices – instead add gradually 2-3 devices – Fuse can be fragile when 8-16 devices at once tries to create new connection
• When using USB Hub please connect devices one by one to the ascending USB ports – it will help you to distinguish which of them had failed and needs to be recovered by Recovery plugin (check IMEI, USB Port # from UI or follow Action Report log for details)
• Do not connect\disconnect devices while other flashings are in progress – all should be finalized (successful or not) – main reason for fail is USB port enumeration done by OS when changing something
• Additional info for 16 simultaneous flashes: Based on testing with Windows Phone 8 devices please follow the following preliminary recommendations for a PC USB setup for maximum stability and timing of the USB bus:
• Use a PC that has at least four (4) independent USB 2.0 host controllers.
• Connect no more than one powered external USB hub to each host controller
• Each external hub must have its own independent power source,  with the capability to supply at least 500 mA per device connected to it.
• Connect no more than four (4) devices to each external hub
 
Supported products:
RM-761, RM-763, RM-781, RM-799, RM-800, RM-813, RM-884, RM-803, RM-809, RM-807, RM-832, RM-834, RM-810, RM-811, RM-812, RM-827
RM-837, RM-871, RM-808, RM-823, RM-802, RM-835, RM-836, RM-849, RM-724, RM-725, RM-819, RM-801, RM-596, RM-601, RM-609, RM-626
RM-639, RM-640, RM-659, RM-662, RM-670, RM-675, RM-679, RM-691, RM-692, RM-693, RM-694, RM-702, RM-704, RM-707, RM-718, RM-730
RM-749, RM-750, RM-754, RM-772, RM-774, RM-775, RM-776, RM-779, RM-766, RM-767, RM-768, RM-696, RM-714, RM-872, RM-873, RM-862
RM-863, RM-864, RM-824, RM-825, RM-826, RM-845, RM-867, RM-846, RM-852, RM-821, RM-820, RM-822, RM-889, RM-898, RM-907, RM-878
RM-838, RM-843, RM-911, RM-913, RM-914, RM-915, RM-917, RM-923, RM-885, RM-887, RM-860, RM-839, RM-840, RM-841, RM-919, RM-921
RM-924, RM-925, RM-926, RM-928, RM-929, RM-892, RM-893, RM-899, RM-900, RM-902, RM-910, RM-875, RM-876, RM-877, RM-927, RM-937
RM-938, RM-939, RM-940, RM-941, RM-942, RM-943, RM-948, RM-949, RM-950, RM-952, RM-953, RM-954, RM-955, RM-956, RM-957, RM-920
RM-922, RM-944, RM-945, RM-947, RM-951, RM-958, RM-959, RM-961, RM-962, RM-963, RM-994, RM-995, RM-996, RM-997, RM-998, RM-934
RM-972, RM-973, RX-113, RX-114, RM-969, RM-970, RM-971, RM-980, RM-986, RM-987
  

Full: Download Now

MSI: Download Now

30 Replies to “Nokia Care Suite PST 5.0 5.0.60.1409”

  1. lo instale correctamente — pero me abre en modo offline— y me pide usuario y pass— ayuda !

  2. you said :supported in this release, old PST and Multi SW Updater version 2011.50.2 or Phoenix release needs to be used.
    i cant install last release so have i install old release first and then last release ?
    if yes ..which release use ?

    1. No, you do not need to install the old version first when you want to install the latest one. Please read all the words in the sentence.

  3. hi,
    i forget my nokia e5 password ..
    how can i company resat my phone via nokia care suite? ..

      1. but when i try to install latest one after delete the older. i didn’t find the short cut on desk top and i didn’t find the folder ncs on c pation
        and i didnt find it on start menu
        all program – whats the problem ?

      2. but when i try to install latest one after delete the older. i didn’t find the short cut on desk top and i didn’t find the folder ncs on c pation
        and i didnt find it on start menu
        all program – whats the problem ?
        – although when i reinstall the old release i find it .and it works.
        ??????

  4. my nokia N 73 is not displaying any content or not switcing on. last time it was on during updating software. i was updating firmware through nokia software updater. and pc turned off. after that my phone is not working. ehat do i do ?
    when i connect it to pc its showing me usb device connected but not working.

  5. Hello,
    I would like to ask, if it is possible to download any firmware for RM-820 through Seidea login? I have tried to download multiple firmwares both through Care Suite and Data Package Manager without any success. I always end up with “Access is denied. Verify credentials.” or endless loading screen (for Data Package Manager)…
    Is it possible to obtain Nokia Account login somehow to be able to use official access?

    Thank you very much for any help.

      1. Thank you very much.
        Firmware was downloaded via Navifirm without any problems. Only now I have a different one. Even thought I move downloaded files to /ProgramData/Nokia/Packages/rm-821/ I cannot see them in Nokia Care… I have tried already multiple versions (both of Care Suite and different firmware variants without any success. Should I rename the files somehow – their names are like RM821_059R4H5_3051.40000.1349.0003_046? I have tried to google the problem but haven’t find anything conclusive…

        Thank you again for any kind of help.

  6. I can not install this version……

    the last version that did not give me error in installation was Nokia Care Suite PST 5.0 2013.13.4.4

    do not understand why????

Leave a Reply to Honza Cancel reply

Your email address will not be published. Required fields are marked *